diff options
Diffstat (limited to 'docs/Samba-Guide/SBE-SimpleOfficeServer.xml')
| -rw-r--r-- | docs/Samba-Guide/SBE-SimpleOfficeServer.xml | 18 |
1 files changed, 9 insertions, 9 deletions
diff --git a/docs/Samba-Guide/SBE-SimpleOfficeServer.xml b/docs/Samba-Guide/SBE-SimpleOfficeServer.xml index 3f1539cc11..404b9032d8 100644 --- a/docs/Samba-Guide/SBE-SimpleOfficeServer.xml +++ b/docs/Samba-Guide/SBE-SimpleOfficeServer.xml @@ -85,7 +85,7 @@ Mr. Bob Jordan has asked you to install the new server as economically as possible. The central server has a Pentium-IV 1.6GHz CPU, 768MB RAM, a 20GB IDE boot drive, a 160GB IDE second disk to store plans, and a 100-base-T Ethernet card. You have already installed Red Hat Fedora Core2 and - have upgraded Samba to version 3.0.12 using the RPM package that is provided from the Samba + have upgraded Samba to version 3.0.15 using the RPM package that is provided from the Samba <ulink url="http://www.samba.org">FTP</ulink> sites. </para> @@ -140,7 +140,7 @@ <para> It is assumed that the server is fully installed and ready for installation and - configuration of Samba 3.0.12 and any support files needed. All TCP/IP addresses + configuration of Samba 3.0.15 and any support files needed. All TCP/IP addresses have been hard coded. In our case the IP address of the Samba server is <constant>192.168.1.1</constant> and the netmask is <constant>255.255.255.0</constant>. The host name of the server used was <constant>server</constant>. @@ -163,7 +163,7 @@ Install the RPM package as using either the Red Hat Linux preferred GUI tool or using the <command>rpm</command>, as follows: <screen> -&rootprompt; rpm -Uvh samba-3.0.12-1.i386.rpm +&rootprompt; rpm -Uvh samba-3.0.15-1.i386.rpm </screen> </para></step> @@ -293,12 +293,12 @@ Sharename Type Comment --------- ---- ------- Plans Disk - IPC$ IPC IPC Service (Samba 3.0.12) - ADMIN$ IPC IPC Service (Samba 3.0.12) + IPC$ IPC IPC Service (Samba 3.0.15) + ADMIN$ IPC IPC Service (Samba 3.0.15) Server Comment --------- ------- - SERVER Samba 3.0.12 + SERVER Samba 3.0.15 Workgroup Master --------- -------- @@ -409,7 +409,7 @@ 5 PS printers that are network connected. The second printer is to be used for general office and letter printing. Your recommendation to allow only the Linux server to print directly to the printers was accepted. You have supplied SUSE Enterprise Linux Server 9 and - have upgraded Samba to version 3.0.12. + have upgraded Samba to version 3.0.15. </para> <sect3> @@ -495,7 +495,7 @@ <para> It is assumed that the server is fully installed and ready for configuration of - Samba 3.0.12 and for necessary support files. All TCP/IP addresses should be hard coded. + Samba 3.0.15 and for necessary support files. All TCP/IP addresses should be hard coded. In our case, the IP address of the Samba server is 192.168.1.1 and the netmask is 255.255.255.0. The host name of the server used was <constant>server</constant>. The office network is built as shown in <link linkend="charitynet"/>. @@ -943,7 +943,7 @@ C:\WINDOWS: regedit ME-dpwc.reg <para><indexterm> <primary>Red Hat Linux</primary> </indexterm> - The new server will run Red Hat Fedora Core2. You should install Samba-3.0.12 and + The new server will run Red Hat Fedora Core2. You should install Samba-3.0.15 and copy all files off the old system to the new one. The existing Windows NT4 server has a parallel port HP LaserJet 4 printer that is shared by all. The printer driver is installed on each workstation. You must not change anything on the workstations. Mr. Meany gave instructions to |